How to Align Garage Door Sensors Chamberlain

    Is your garage door not opening or stuck wide open? Looking for a professional repair technician?

    Get in touch with our garage door repair team and help is on it’s way! When it comes to garage door Services in Philadelphia and its surroundings, Better leave it up to the professionals. For a FREE quote and estimate..

    CALL NOW: ☎️ (267) 651-0259

    Or, fill out this form and we will contact you shortly




    Show us the damage: Send us some photos for a FREE cost estimate.

    How to Align Garage Door Sensors Chamberlain

    How to Align Garage Door Sensors Chamberlain

    Modern garage doors have evolved to become more convenient and easy to use; however, problems within the system can be quite problematic.

    If you’ve experienced your garage door not opening or reversing as it is closing, then you might have a problem with your sensors.

    Rest easy, you don’t have to call and spend for professional help to get this problem fixed if it’s only minor; you can do it yourself!

    For more on how to align garage door sensors in Chamberlain, read further:

    Garage Door Sensors

    As a safety measure required by the law since the 1990s, garage door sensors are used to reduce accidents involving garage doors.

    Modern garage door openers are now equipped with these sensors to halt or reverse the door’s travel if something is blocking its path.

    This way, children or pets are not at risk of getting hurt or killed from the crushing weight of the large garage door.

    How Garage Door Sensors Work

    Garage door sensors come in paired units that are placed on either side of the garage doorway typically placed 6 inches above the ground.

    As a pair, one unit (emitter) continuously sends a signal and the other unit (receiver) receives it, and the way to trigger sensors’ task is to disrupt the signal.

    Hence, if an object is obstructing the emitter from sending a beam to the receiver, then the door reverses from its downward travel.

    Moreover, a flashing light will appear to indicate that the sensors detect something resulting in the motor not closing the door until the obstruction is cleared.

    What Are Signs of Faulty Sensors?

    Aligning Garage Door Sensors

    Misaligned garage door sensors can be irritating as it disrupts normal garage door operations.

    Unless the sensors are back in alignment, your garage door might not cease from reversing every time you try to close it.

    Don’t worry, as mentioned, you can do the realignment of your sensors without relying on hiring a professional garage door technician.

    For the exact details on how to align garage door sensors in Chamberlain, below are the things you will need and the procedure to follow:

    Things You Will Need

    Before beginning the procedure of realigning your garage door sensors, be sure to prepare the following items:

    • Gloves (electricity-resistant)
    • String
    • Screwdriver
    • Level

    Once you’ve gathered these, you can begin the process by following the steps below:

    Step 0: Try Lightly Jiggling the Sensor into Alignment

    Before doing any major adjustments, lightly jiggle the sensor in place to see if it works.

    To know if it gets fixed with this method, both sensors should have a green light on.

    If it doesn’t work, proceed to step 1.

    Step 1: Disconnect Your Garage Door System from the Power Supply

    Wearing your electricity-resistant gloves, turn off the power supply to your garage from the breaker box or unplug the sensors from its outlet.

    Doing this ensures that you are not risking getting electrocuted while you’re realigning your garage door sensors.

    Step 2: Unscrew the Bracket Mounting the Sensors

    Using a screwdriver, unscrew the bracket holding the sensors so that they’re loose enough to move up and down.

    Note that you don’t have to fully unscrew the screws; simply loosen them.

    Step 3: Tie a String to Run Across Both Sensors

    After you’ve loosened the mounting bracket, get a long string that’s easy to tie and remove.

    Using the long string, tie each end on the center of each sensor.

    The string should run along in a straight line from the emitter to the receiver.

    Step 4: Level the String

    Using the string as a guide, align the sensors by moving them up or down.

    To ensure that the string runs parallel to the ground, use a level and press it against the string.

    Once the level shows that the string is properly aligned, move on to the next step.

    Step 5: Tighten the Screws

    Before tightening the screws, make sure that you don’t move the sensors from their aligned positions.

    Tightening the screws can move the sensors a bit off from where you intended it to be, so be sure to be extra careful when doing this.

    To ensure that the sensors are still aligned, both the emitter and the receiver should have green lights on.

    Step 6: Turn on the Power Supply and Test the Sensors

    After tinkering with the sensors’ positions, turn on the power supply and check if they are functional.

    Run the opener in a full opening and closing cycle and see if the closing door has stopped reversing on its own.

    Also, check if the safety reversal feature gets activated with an actual obstruction.

    If you observe these, then you’re good to go!

    We hope you enjoyed the above article titled How to Align Garage Door Sensors Chamberlain. For more great articles such as “How to Align Garage Door Sensors Chamberlain”, feel free to browse our blog for more great content. Garage Doors Philly.

    Recommended articles

    How To Open Garage Door Manually

    How To Open Garage Door Manually

    Garage doors are supposed to protect us from outside harm, but there are some cases wherein they bring trouble. Unexpectedly you find yourself locked outside your garage or trapped inside it. Instead of panicking, consider ways to open your garage door manually. It is genuinely

    Read More »
    Tags
    chamberlain garage door opens by itself, crease in garage door, garage door adjustment do it yourself, garage door dent removal repair, garage door dent repair near me, garage door installation, garage door installation cost, garage door installation near me, garage door installation philadelphia, garage door maintenance cost, garage door maintenance kit, garage door maintenance service near me, garage door not opening but motor running, garage door opens a little then stops, garage door opens by itself after closing, garage door opens sporadically, garage door remote not working, garage door repair, garage door repair 19116, garage door repair 19147, garage door repair 19152, garage door repair in philadelphia, garage door repair near me, garage door repair philadelphia, garage doors, garage doors in philadelphia pa, garage doors near me, garage doors prices, garage door wall switch not working, garage door won't open manually, hit garage door with car how to fix, how much does it cost to install a double garage door?, how to adjust a garage door that is crooked, how to fix a bent garage door panel, how to fix a dent in a vinyl garage door, how to fix up and over garage door cable, how to install garage door springs and cables, how to open a stuck garage door from the outside, liftmaster garage door opener troubleshooting, lowe's garage door installation cost, merlin garage door opening by itself, philly doors, rolling gate repair philadelphia, why garage door opened for no reason, youtube garage door opens by itself
    Contact Us
    COVID-19 NOTICE:
    Our technicians are equipped with masks and gloves complying with health and safety regulations.
    This is default text for notification bar